我们在工程项目中经常会遇到MCU串口不够的情况，更换MCU成本又会增加，那该怎么办呢？于是就有了这篇文章，我们可以使用普通IO口加上定时器去模拟串口发送接收的功能，这样就完美解决串口不够用的问题了，但是这样做会有一些缺点，比如速度不能太快，没有关于串口的DMA等，我测试在9600波特率下完全没有问题，下面是源码，需要的话可以参考1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
18
19
20
21
22
23
24
25
26
27
28
29
30
31
32
33
34
35
36
37
38
39
40
41
42
43
44
45
46
47
48
49
50
51
52
53
54
55
56
57
58
59
60
61
62
63
64
65
66
67
68
69
70
71
72
73
74
75
76
77
78
79
80
81
82
83
84
85
86
87
88
89
90
91
92
93
94
95
96
97
98
99
100
101
102
103
104
105
106
107
108
109
110
111
112
113
114
115
116
117
118
119
120
121
122
123
124
125
126
127
128
129
130
131
132
133
134
135
136
137
138
139
140
141
142
143
144
145
146
147
148
149
150
151
152
153
154
155
156
157
158
159
160
161
162
163
164
165
166
167
u8 len = 0; //接收计数
u8 USART_buf[11]; //接收缓冲区
enum {
COM_START_BIT,
COM_D0_BIT,
COM_D1_BIT,
COM_D2_BIT,
COM_D3_BIT,
COM_D4_BIT,
COM_D5_BIT,
COM_D6_BIT,
COM_D7_BIT,
COM_STOP_BIT,
};
u8 recvStat = COM_STOP_BIT;
u8 recvData = 0;
void IO_TXD(u8 Data)
{
u8 i = 0;
OI_TXD = 0;
delay_us(BuadRate_9600);
for(i = 0; i < 8; i++)
{
if(Data&0x01)
OI_TXD = 1;
else
OI_TXD = 0;
delay_us(BuadRate_9600);
Data = Data>>1;
}
OI_TXD = 1;
delay_us(BuadRate_9600);
}
void USART_Send(u8 *buf, u8 len)
{
u8 t;
for(t = 0; t < len; t++)
{
IO_TXD(buf[t]);
}
}
void IOConfig(void)
{
GPIO_InitTypeDef GPIO_InitStructure;
NVIC_InitTypeDef NVIC_InitStructure;
EXTI_InitTypeDef EXTI_InitStruct;
RCC_APB2PeriphClockCmd(RCC_APB2Periph_AFIO|RCC_APB2Periph_GPIOB|RCC_APB2Periph_GPIOC, ENABLE); //使能PB,PC端口时钟
//SoftWare Serial TXD
GPIO_InitStructure.GPIO_Pin = GPIO_Pin_13;
GPIO_InitStructure.GPIO_Mode = GPIO_Mode_Out_PP; //推挽输出
GPIO_InitStructure.GPIO_Speed = GPIO_Speed_50MHz; //IO口速度为50MHz
GPIO_Init(GPIOC, &GPIO_InitStructure);
GPIO_SetBits(GPIOC,GPIO_Pin_13);
//SoftWare Serial RXD
GPIO_InitStructure.GPIO_Pin = GPIO_Pin_14;
GPIO_InitStructure.GPIO_Mode = GPIO_Mode_IPU;
GPIO_InitStructure.GPIO_Speed = GPIO_Speed_50MHz;
GPIO_Init(GPIOB, &GPIO_InitStructure);
GPIO_EXTILineConfig(GPIO_PortSourceGPIOB, GPIO_PinSource14);
EXTI_InitStruct.EXTI_Line = EXTI_Line14;
EXTI_InitStruct.EXTI_Mode=EXTI_Mode_Interrupt;
EXTI_InitStruct.EXTI_Trigger=EXTI_Trigger_Falling; //下降沿触发中断
EXTI_InitStruct.EXTI_LineCmd=ENABLE;
EXTI_Init(&EXTI_InitStruct);
NVIC_InitStructure.NVIC_IRQChannel= EXTI15_10_IRQn ;
NVIC_InitStructure.NVIC_IRQChannelPreemptionPriority=2;
NVIC_InitStructure.NVIC_IRQChannelSubPriority =2;
NVIC_InitStructure.NVIC_IRQChannelCmd=ENABLE;
NVIC_Init(&NVIC_InitStructure);
}
void TIM4_Int_Init(u16 arr,u16 psc)
{
TIM_TimeBaseInitTypeDef TIM_TimeBaseStructure;
NVIC_InitTypeDef NVIC_InitStructure;
RCC_APB1PeriphClockCmd(RCC_APB1Periph_TIM4, ENABLE); //时钟使能
//定时器TIM4初始化
TIM_TimeBaseStructure.TIM_Period = arr; //设置在下一个更新事件装入活动的自动重装载寄存器周期的值
TIM_TimeBaseStructure.TIM_Prescaler =psc; //设置用来作为TIMx时钟频率除数的预分频值
TIM_TimeBaseStructure.TIM_ClockDivision = TIM_CKD_DIV1; //设置时钟分割:TDTS = Tck_tim
TIM_TimeBaseStructure.TIM_CounterMode = TIM_CounterMode_Up; //TIM向上计数模式
TIM_TimeBaseInit(TIM4, &TIM_TimeBaseStructure); //根据指定的参数初始化TIMx的时间基数单位
TIM_ClearITPendingBit(TIM4, TIM_FLAG_Update);
TIM_ITConfig(TIM4,TIM_IT_Update,ENABLE ); //使能指定的TIM3中断,允许更新中断
//中断优先级NVIC设置
NVIC_InitStructure.NVIC_IRQChannel = TIM4_IRQn; //TIM4中断
NVIC_InitStructure.NVIC_IRQChannelPreemptionPriority = 1; //先占优先级1级
NVIC_InitStructure.NVIC_IRQChannelSubPriority = 1; //从优先级1级
NVIC_InitStructure.NVIC_IRQChannelCmd = ENABLE; //IRQ通道被使能
NVIC_Init(&NVIC_InitStructure); //初始化NVIC寄存器
}
int main(void)
{
NVIC_PriorityGroupConfig(NVIC_PriorityGroup_2);//设置中断优先级分组为组2：2位抢占优先级，2位响应优先级
delay_init();
IOConfig();
TIM4_Int_Init(107, 71); //1M计数频率
while(1)
{
if(len > 10)
{
len = 0;
USART_Send(USART_buf,11);
}
}
}
void EXTI15_10_IRQHandler(void)
{
if(EXTI_GetFlagStatus(EXTI_Line14) != RESET)
{
if(OI_RXD == 0)
{
if(recvStat == COM_STOP_BIT)
{
recvStat = COM_START_BIT;
TIM_Cmd(TIM4, ENABLE);
}
}
EXTI_ClearITPendingBit(EXTI_Line14);
}
}
void TIM4_IRQHandler(void)
{
if(TIM_GetFlagStatus(TIM4, TIM_FLAG_Update) != RESET)
{
TIM_ClearITPendingBit(TIM4, TIM_FLAG_Update);
recvStat++;
if(recvStat == COM_STOP_BIT)
{
TIM_Cmd(TIM4, DISABLE);
USART_buf[len++] = recvData;
return;
}
if(OI_RXD)
{
recvData |= (1 << (recvStat - 1));
} else {
recvData &= ~(1 << (recvStat - 1));
}
}
}
